make your own network wire It can save you time and money, as well as give you the satisfaction of doing it yourself. It may seem complicated at first, but with the right instructions and a little practice, anyone can do it. In this article, we will show you how to make network cable step by step, with all the materials and tools you will need. You don't need to be a tech expert to be able to accomplish this task, just a little patience and attention to detail. Let's start!

– Step by step -- How to Make Network Cable?

• Step 1: Gather the materials needed to make the network cable. You will need to two RJ45 connectors, a network cable (also known as an Ethernet cable), a wire stripper and a crimping pliers.
• Step 2: Use the wire stripper to remove approximately 2.5 cm of the outer sheath of the network cable to expose the internal cables.
• Step 3:Sort the internal cables according to the wiring standard you are going to use (normally the T568B or T568A standard is used). Wire colors must follow a specific order to ensure proper connection.
• Step 4: Insert the cables neatly into the RJ45 connector, making sure each wire is in the correct position and fully inserted into the connector.
• Step 5: Use the crimping pliers to Adjust and secure the cables in place inside the RJ45 connector. Make sure you apply enough pressure to ensure a solid connection.
• Step 6: Repeat the same steps on the other end of the network cable, making sure both ends of the cable are in the same wiring standard.
• Step 7: Once you have finished attaching the connectors to both ends of the cable, perform a continuity test to make sure the connection is successful.

FAQ

1. What materials do I need to make a network cable?

1. Category 5e or 6 UTP cable.
2. RJ45 connectors.
3. Crimper.
4. Scissors or cold cutters.
5. Flat tip screwdriver.

2. How much cable do I need to make a network cable?

1. It depends on the distance between the device and the router, generally it is calculated a little more than necessary to avoid falling short.

3. What is the process to make a network cable?

1. Cut the UTP cable to the desired length.
2. Remove an inch of the outer covering of the cable.
3. Sort cables according to the T568A or T568B standard.
4. Insert the cables into the RJ45 connector.
5. Use the crimping tool to secure the connector to the cable.

4. What network cabling standards exist?

1. T568A Standard
2. T568B Standard

5. How do I know which wiring standard to use?

1. It depends on the wiring system of the network into which the cable is to be connected.
2. If there is no defined standard, either standard can be used, as long as the same one is used at both ends of the cable.

6. Why is it important to follow a wiring standard?

1. To ensure compatibility with other network devices.
2. To ensure optimal network performance.

7. What should I do if my network cable is not working?

1. Verify that the cables are correctly connected to the RJ45 connectors.
2. Make sure the appropriate wiring standard has been used at both ends of the cable.
3. Check that the connectors are correctly crimped.
4. Try a different cable to rule out wiring problems.

8. Can I reuse an RJ45 connector to make a new network cable?

1. Yes, as long as the connector is not damaged and the cables are in good condition.
2. It is important to ensure that the wires are inserted correctly into the connector before crimping it again.

9. Is it possible to make a network cable without a crimping tool?

1. It is not recommended, since the crimping tool is the necessary tool to secure the RJ45 connector to the cable.
2. However, a similar result can be achieved by using a splicing method and securing the wires with electrical tape, although it will not be as reliable as the traditional method.

10. What precautions should I take when making a network cable?

1. Use appropriate tools to avoid damaging cables or connectors.
2. Check the integrity of the cables before making connections.
3. Do not expose the cables to sources of heat or excessive humidity.

You may also be interested in this related content:

• How do you know if someone has Google Hangouts?
• How to join a meeting by phone in BlueJeans?
• How do I get to Tepotzotlan?